![]() ![]() I Finished this top with BLO and spar Urethane. Using the sled is very simple, just set the router to the desired depth and push it across the bridge. The bridge is constructed the same was as the base, except is has a slot in the center for the router bit to pass through. The slides are dual purpose, they insure the base is flat and they provide an elevated surface for the bridge to rest on. The bottom is a single layer and the sides are two layers screwed together, & to the base with drywall screws. I made a large tabletop from pallet blocks and needed a way to flatten it, and I didn. Since I have never used a router sled before, I decided to make a small one and use it to make some tops for my role-away tool chests. This router sled planer jig is my entry into the woodjigs21 challenge. One night while surfing SawmillCreek, I stumbled across a post that referenced a simple shop made tool called a router sled that wold let me flatten a bench top or any other large wood surface with tools I already have. I used this circle saw and this trac k, but you could use a table saw as well. ![]() I only have a 13″ planer, so I thought I would have to wait till i got a bigger planer, or pay someone else to plane the top. After a 60 grit sanding with the Rotex first to remove the mill marks and then progress in grit to 220 with a random orbit sander and you get a smooth flat finish.Eventually I plan to build a workbench with a hard maple top. Once you’re done, remove the router and the sled and sweep off your work. Note, I didnt need the shim anymore because this side was now flat. Once you surface one side, flip your work over and repeat the process. Now slowly move onto the surface of the workpiece and make your first cut by slowly passing the router over the surface, adjusting it about 3/4″ on each pass. Make sure your router bit is away from the surface of the workpiece and turn the router on. I also used a shim here to remove any rocking. ![]() Since the work piece weighs over 40 lbs, there’s no need to fasten it down, it will stay in place. To hold my workpiece in place, I used 150 lb mag switches to keep the work piece from moving laterally. Base Cabinet Plans 10.00 Add to cart Coping Sled Plans 5.00 Add to cart The Cabinet Plan Bundle 24.99 Add to cart Upper. Be the first to review Slab Flattening Mill Plans Cancel reply. Just plunge down until the bit makes contact. You can get it done with your router and 1/2 sheet of plywood MWA WOODWORKS BUILDLEARNREPEAT 0,00 USD. Now with the router OFF, find the lowest point on the surface of the material. This tool gives you the ability to extend all the way down to the workpiece. I used a 1 1/4″ mortising bit, but I could have used a surfacing bit just as easily. Now just cut the sides for the sled with a miter saw. Once again, exercise caution with your hands and keep them well away from the blade. Make sure when you cut the other side that you secure the waste piece in the middle with your fingers so that it doesn’t wander into the blade and cause kickback. Now run the piece across the blade until you reach the holes on either end. ** PLEASE USE CAUTION** always be aware of where your hands are with regard to the blade since you are blindly raising the blade through the work piece. Turn on your saw and slowly raise the blade up through the plywood. Use feather boards to keep constant downward and lateral pressure against the work piece.With the saw blade retracted, slide the work piece over the blade. This will serve as the beginning and end of the slot. At the drill press, drill two 1 1/2″ holes at either end of the sled bottom. Explore Mikes board 'Router sled' on Pinterest. See more ideas about router sled, router, woodworking. ![]() Anyone can do this with the right plans Buying diy tiny homes storage. Plus, get Fine Woodworking emails filled with plans, how-to, and special offers. A friend did this and it turned out great. Add 1/32″ to this measurement to allow just enough room to prevent binding when the router moves across the sled. Nick Offermans shopmade router jig flattens thick slabs to create. To cut the bottom of the sled, use your router’s base to set the width of the cut. ![]()
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |